Just how do you actually feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bath tub with a brand-new one is also a moderately tough project. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall surface to remove the old tub and also position the new tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require an assistant to move out the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task as well as fit attempting it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration employing one before you begin. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly help you install a new tub in your shower room if you have actually currently gotten a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your devices and material list need to consist of the following:
Preparing for the Setup
First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to ensure that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets device to stop strain on the tub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water supply. After doing so, activate the faucets to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed position. The wooden boards are handy in equally spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Switch on the water as well as check all joints as well as new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet as well as the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly resolve it into its final placement.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin making certain that the washers are in location between the faucet and also the sink. Protect the tap in place with the manufacturer provided backnut. Once the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be linked to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack an inflexible seal, causing the water to pass through the wall between the bathroom and the tiling, bring about problems with wetness and feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that entry about A Step-by-Step Guide to Installing a Bathtub when surfing the web. Appreciated our review? Please share it. Help other people locate it. Many thanks for your time. Please pay a visit to our site back soon.
Book Now!